remove the shredder from its carton and unwind the cord

Dec, 24 2019
Senior R&D TeamSuperb ManufacturingQuality Service

SDIER Machinery offers customized shredding and crushing/granulating solutions. The solutions provided by SDIER are well recognized by customers and are widely used in the treatment and recycling of various solid wastes.

Compared with our competitors, SDIER's equipment advantages are durability and reliability, while taking into account cost performance.

The solutions we provide have a wide range of material applicability and high production capacity, which have been widely proven all over the world.

We have a wealth of product information and customer cases, you are welcome to contact us to obtain them. We design plans and manufacturing equipment based on the types of materials. We cannot give a quotation online. Please fill in the form below and we will contact you as soon as possible.

Information Request

Please fill in the following form, we will respond your request in 24 hours.

Materials:

Owner’s Manual Compact Series Kitchen Machines for models

(MUZ4MX2), continuous shredder (MUZ4DS2) with shedding, slicing and grating discs, high-speed drive cover and accessory holder. Unpacking Carefully remove the power unit from its packaging and place it on the counter so it is ready to use. As you remove the accessories from the carton, check them against Figure 1 to ensure that all the 5 H.P. CHIPPER-SHREDDER a Remove engine oilfillplug. See figure 7. b. With chipper-shredder level, fill engine with oil to point of overflowing. Capacity is 1-1/4 pints c Tilt chipper-shredder forward on its wheels, then re-level. d Check oil level, Refill to point of over-flowing if necessary. Replace oil fill plug. jo_ \'tll))i Plug t OilDrain Plug FIGURE 7. Fuel ...

Fellowes T7CM Trigger Sensor Replacement

Remove the shredder from the catch basket and place the silver side down on a flat surface. ... Step 5 Main Power Cord . Remove the wire holder. This is a small screwed in piece of plastic which holds the wires in place. The screw length is 10 mm and the head diameter is 6 mm. Paper Shredder Setting up the shredder 1. Remove the shredder from the packaging and unwind the cord to its full length. 2. Place the waste bin on a firm level surface in a stable upright position. 3. This appliance is equipped with a safety system. The waste bin should be fully pushed inside the appliance, otherwise the appliance will not operate. 4.

OPERATIONAL MANUAL

1. The 100X shredder should be placed on a flat level surface. 2. Place the shredder head securely on top of the wastebasket. 3. Make sure that the wastebasket is completely inserted in to the shredder cabinet and that it fits flush with the shredder cabinet. 4. Plug the power cord into any standard 115-volt AC outlet. 5. Instruction Manual • Never place the shredder near water or any heat source. • Do not use the shredder if the power cord is damaged in any way. • Do not attempt to service this product yourself as doing so may expose you to sharp cutting blades and/or electricity and will void the manufacturer's warranty. • Never try to clean or clear the shredder blade.

GoECOlife GMW81B 8-Sheet Level 4 Micro-Cut Shredder

power cord before opening the shredder. 6. This product should never be placed near a radiator or other heat source. 7. Do not allow anything to rest on the power cord. Do not place the power cord where people may walk on it. 8. If an extension cord is used with this product, make sure the total ampere (amps) ratings ProAction VS1208CD manual If power supply cord is damaged, it must replaced by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard. 5 Page: 6 Before first use User Instructions Setting up the shredder 1. Remove the shredder from the packaging and unwind the cord to its ...

Owner’s Manual

10. Do not place hands or fingers into the shredder opening as serious injury could result. 11. Never allow children to operate or play with this shredder. 12. Do not operate the machine for any other purpose other than its intended use. 13. It is recommended to remove all staples from paper before shredding. Instruction Manual Remove the shredder from its packaging and check to make sure it is in good condition before using. ... hredder if the Power Cord is damaged. If the Power Cord is damaged it must be ... Remove the shredder from the outer carton and place the shredder head on top of the waste bin,

SHR3D IT - Compact Plastic Shredder and Recycler

Given the state of our planet and its finite resources, recycling and reusing what we have is the only way ahead. SHR3D IT is a good step in this direction. Through this desktop plastic processor, we hope to encourage widespread reuse of old plastics, thereby promoting sustainable and environment-friendly practices. GS1400 - 2helpU Remove keys and adjusting wrenches ... Never carry the tool by its cord or pull it to disconnect from the socket. Keep the cord away from heat, oil and sharp edges. ... When using a cable reel, always unwind the cable completely. CARTON CONTENTS The carton contains: 1 Shredder ...

Paper Shredder

Setting up the shredder 1. Remove the shredder from the packaging and unwind the cord to its full length. 2. Place the waste bin on a firm level surface in a stable upright position. 3. Take the main unit and put it onto the waste bin. Ensure that the alignment marks on the shredder head and waste bin are in line. 4. SILENT SHREDDER Remove the silent shredder and its contents from within the carton. 1. Carefully place the machine upside down resting on the feeding hopper. Position the legs ensuring they are assembled so that they are angled outwards (fig.1). 2. Secure the legs to the machine with the washers and hex-screws, using the 6mm allen key provided (fig.1). 3.

MODEL: BT-38SM Operating Instructions Manual

Carefully remove the unit from the display carton and remove all packing material from the unit. Unwind the AC power cord and extend it to its full length. Unwind the FM Antenna wire and extend it to its full length. Place the unit on a stable, level surface, convenient to ... Owner’s Manual Compact Series Kitchen Machines for models (MUZ4MX2), continuous shredder (MUZ4DS2) with shedding, slicing and grating discs, high-speed drive cover and accessory holder. Unpacking Carefully remove the power unit from its packaging and place it on the counter so it is ready to use. As you remove the accessories from the carton, check them against Figure 1 to ensure that all the

Owner’s Manual Universal Series Kitchen Machines for models

whisks, dough hook, slicer/shredder (MUZ 6 RR2) with universal beater (MUZ 6 RG3) and motor drive cover. Unpacking Carefully remove the power unit from its packaging and place it on the counter so it is ready to use. As you remove the accessories from the carton, check them against figure 1 to assure that all the standard parts are present. Cardboard Shredder and Perforators - www.zakzory.pl The shredder is available in two versions, a 240 voltage or a 480 voltage. The difference is that the 240 runs a bit slower and is less powerful than the 480. When a possible jam occurs, you can hit reverse to reverse the cutting cylinders so you can remove the jammed cardboard. Capacity: 1-2 layers; Motor: 1.8 kW; Power supply: 240 / 480 V

How to Clear a Clogged Paper Shredder

Depending on your shredder model, you may be able to remove the top of the shredder for easier access. Step 5. Reconnect the power cord to the shredder and turn on the device. Insert a single piece of paper into the blades as a test. The paper should move smoothly through the shredder blades if you removed the clog successfully. Paper Shredder Setting up the shredder 1. Remove the shredder from the packaging and unwind the cord to its full length. 2. Place the waste bin on a firm level surface in a stable upright position. 3. Take the main unit and put it onto the waste bin. Ensure that the alignment marks on the shredder head and waste bin are in line. 4.

A16CC17 User Manual-01new

t Always turn the shredder off and unplug the power cord when: not in use, before cleaning it, moving it, or emptying the waste basket. ... Slide the power switch to Reverse mode and remove paper at a 45º angle. ENGLISH 7 OPERATION Power On: Green light – Power light will only activate when paper/media is inserted to shred. Shredder Troubleshooting FAQ - www.zakzory.pl 2. With the shredder unplugged, you may use a set needle-nose pliers or tweezers to remove the blockage. 3. Use the "Reverse" mode to back up and remove the stuck paper. The shredder will back up and loosen the jammed paper. If required, you may need to tug and remove several sheets to effectively clear the machine.

How To Clean Paper Shredder Properly

Whenever you notice that shredder getting slower to cut the paper and often creating odd sounds, you should clean it immediately. Because a long term jam can occur great worse for your device. First of all, remove the plug of your device and remove the previous cutting paper waste from the shredder ... OWNER’S MANUAL its own legs (included with unit) •Easily replaceable cutting cords with extras sup-plied with each unit. B .U n p a cking Instructions Your unit has been carefully packed at the factory to prevent damage during shipment and storage. Carefully unpack the carton as follows: www.zakzory.ple contents from carton www.zakzory.pl parts against list shown.

Paper Shredder Safety

Inspect the electrical cord and plug for defects. If the paper shredder fails the pre-use inspection, notify your supervisor and remove the shredder from service by attaching a red tag that states “OUT OF SERVICE”. Complete red tag with appropriate information. Operating Precautions Locate the paper shredder and power cord outside of foot High Security CD/DVD Shredder FD 8712HS • Unplug the shredder when it is being moved, or if it is not in use for an extended period of time. • Do not disconnect the power by pulling only the cord. Hold the plug when disconnecting. • Keep the shredder away from direct sunlight. • Do not sit on the shredder or place anything on top of it. • Never open the fixed switch or cover.

KitchenAid Rotor Slicer/Shredder Attachment Model RVSA

Assemble Rotor Slicer/Shredder, using fine shredding cone (No. 1). Attach Rotor Slicer/ Shredder to mixer. Turn to Speed 4 and shred carrots into large bowl placed under slicer/ shredder. Set aside. Combine all-purpose flour, whole wheat flour, sugar, baking soda, salt, and nutmeg in mixer bowl. Add oil, pineapple, eggs, and vanilla. www.zakzory.plWS JBSHS360A INSTRUCTION MANUAL Pdf Download Page 2 USING YOUR SHREDDER PRODUCT SPECIFICATION SETTING UP THE SHREDDER Model: JBSHS360A www.zakzory.ple the shredder from its carton and unwind the cord to its full length. Dimension: 310x190x325mm www.zakzory.pl the waste bin on ...

CC412N Instrction Manual

1. Remove the shredder from the outer carton. 2. Place the shredder head on top of the bin. If the Safety Interlock Switch, located underneath the Shredder Head, does not slot into the cut out on top of the Waste Bin correctly, (indicated by the two Safety Interlock stickers found on the back of the Shredder Head and Waste Bin), then the ... Housing SILENT SHREDDER 1. Remove the silent shredder and all components from the carton. 2. Carefully place the shredder housing upside down on a flat surface. 3. Place each leg over the 2 threads on the base of the shredder housing. For maximum stability ensure that the legs are facing outwards. 4. Place a flat washer followed by the locking nut over each of the 4 bolts.

OPERATOR’S MANUAL

gently pulling on the paper to remove it from the shredder. Alternate between forward and reverse, as needed, until the jam clears. • Turn off the shredder, then unplug the power cord. Open the cabinet door and remove the waste bin. Carefully clear any paper shreds that have collected on underside of paper entry. Use care when removing paper ... 57d8dc67e4b071ee4aba304f pdf preview Unwind the power cord fully before use. Keep hands as well as spatulas and other ... and remove the power cord from the outlet before removing the lid from the processing bowl. ... Fine and coarse reversible shredder Spindle Cord storage large pusher in place as it releases o.

User Guide Cross Cut Paper Shredder

5. Insert paper or credit card into feed opening and shredder should begin shredding. 6. Once paper or credit card has cleared the head, shredder should return to standby mode. 1. Unplug the shredder power cord from the electrical outlet. 2. Remove the shredder head from the waste bin by lifting the handle straight up. 3. Empty the waste bin. 4. Slicer/Shredder, w/Unbreakable Bowl (MUZ 7 TS1) Placing Slicer/Shredder into Operation Make sure the power unit is on a smooth, clean, suitable work surface and switched to the Off position, “O/Off.” Unwind the electrical cord to the necessary length and plug into a convenient outlet. The slicer/ shredder is now ready for use. Place items to be sliced, shredded or

SILENT SHREDDER

After removing the silent shredder from the carton, check that the shredder has not been damaged. Unpack the contents. Fitting the wheels and stand 1. Carefully place the shredder housing upside down on a flat surface. 2. Place each leg over the 2 threads on the base of the shredder housing. For maximum stability ensure that the legs are facing ... SC10N Instruction Manual 1. Remove the shredder from the outer carton. 2. Place the shredder head on top of the bin. Shredder Capacity: The SC10N will shred 5 sheets of A4 70g paper at once and will accept paper width up to www.zakzory.pl shredding smaller items like envelopes or credit card receipts, insert them through the middle of the feed slot.

30-SHEET HEAVY-DUTY STRIPCUT

disconnect the power cord before opening the shredder. 6. This product should never be placed near a radiator or other heat source. ... Doing so may damage the shredder. Always remove and unfold envelope contents completely before attempting ... Pack the shredder in its original carton, or equivalent, and write the RA# clearly on the outside of ... How to Take Apart an Aurora Paper Shredder - Paper How to Take Apart an Aurora Paper Shredder. While the Aurora paper shredder is a heavy-duty machine, you can still get it jammed with paper, plastic, or disc www.zakzory.pl thing is that even if it comes with three cutting configurations, it is supposed to be jam-free in most cases.

6-SHEET CROSSCUT

when mounting the shredder on to the wastebasket. 2. Make sure power cord is not damaged in any way and that the outlet is properly functioning. 3. This shredder will safely shred sealed envelopes so long as the number of layers of (folded) paper does not exceed the maximum sheet capacity of the shredder. WM830XA - Aurora Corp shredder. Keep loose clothing or jewelry away from the paper entry slot. Avoid getting hair near the paper entry slot. • Always turn the shredder off and unplug the power cord from the AC outlet when not in use, before cleaning it, moving it, or emptying the waste basket. • RISK OF FIRE.

IDEAL 4006-Cross/Cut

Remove the reusable carton 0 and put a plastic bag in, folding the bag end over the top of the carton (the inside of the carton should be completely filled). Then push the box into the cabinet. c) The power cord must be connected to an independant switchable single phase so-cket. Fuse rating of 16 Amp. max. d) After reading the operating ... Controls - Home | Lenoxx Electronics Australia Pty Ltd Shredder Setup: Remove the shredder from the outer carton and place the shredder head on top of the waste bin. Shredder Capacity: The shredder will shred 5 sheets of A4 70gsm paper at once and will accept paper width up to 220mm. When shredding smaller items like envelopes or

All our shredders have earned the reputation for efficiency, durability and reliability and come with the support of our service and inventory for many years of hassle free operation.

Information Request

Please fill in the following form, we will respond your request in 24 hours.

Materials:

Popular Posts